Results 1 to 4 of 4

Thread: $38 Service Bench

  1. #1
    Baby Twin Fox Fader's Avatar
    Join Date
    Nov 2008
    Location
    Columbus, GA USA
    Posts
    54

    $38 Service Bench

    How to build your own Service Bench.

    First and foremost, props to BBC Racing. Thank you!!


    The "Box"!
    This stand is built from two sheets of 3/4" Marine Grade plywood (There are also a few sections of 1 X 2 used for bracing). Incredibly sturdy! The box will be able to support close to 800 pounds. Locations for handlebar tie-downs when the bike is on the stand. Easy as loading a bike onto a pick-up truck. Held together with friction alone. No fasteners! Quickly disassembles and stores as four 1/2 sheets of plywood. I believe it could be invaluable at the track!

    Parts is Parts!
    The parts of this box are: 2 sides, a top, a back and middle slat, and finally a front slat. You can purchase plywood from Home Depot or Lowes. They will cut twice for free with a vertical table saw with the purchase of the wood. Ask them to "rip" (cut the long way) the sheets down the middle. They will try to cut across the sheets about a 1/2 dozen times before they understand that you need them ripped! Make sure they get as close to center as possible. That's NOT as important as you think. Notice I use the same piece from each sheet as sides. That's in case their saw is off a bit. I suggest marking the pieces before they cut them. You can pay for the extra cuts to make the slats. I did mine myself with a jigsaw.

    Cutting Guide


    While at the store you'll need a couple of lengths of 1" X 2". These were not in the original plans. I added them as stops and braces to the top. The keep the top from sliding on the box once assembled. Grab a handfull of screws long enough to go through the plywood and into the 1" X 2"s.

    Building
    The stand is held together by a series of slots cut in the sides and slats. The slots are just as wide as the plywood is thick. NO SLOP! They are exactly as long as 1/2 the height of the plywood. The slats get slots on the bottoms and sides get slots on the tops. Slots near the ends of the sides should start 3" from the ends. As should the slot's on the back and middle slats.

    Use the middle slat and a centerline mark to mark the position of the slots on the front slat. It will stick out a foot further on the sides than the other slats. I put my middle slat where the center stand of my Futura goes. Use your best judgment. I used a jigsaw to cut the slots. I think a circular saw AND a jigsaw would of been better... but I didn't have a circular saw! I cut inside the lines and did most of my 'fine tuning' with the jigsaw. It took a long time but I'd rather have these fit as tight as possible for strength. They don't need to be too tight, I can take mine apart in less than 2 minutes. Tight, but not stuck.

    Slotting and Assembly Guide


    In the diagram you'll notice the two sections of 1" X 2"s. These screw to the underside of the top. They are situated between the sides and in front of the back and behind the front slats. They provide a bit of strength to the top but are there mainly to keep the top from sliding around. The two holes in the front slat are for tie-downs to the bars or forks.

    Tips
    I firmly suggest two people are used to load a bike! I use a wooden ramp to load the bikes onto the stand. I'm pretty tall so I can walk beside the stand and still support the bike. I think most people will need a step stool to walk up and onto the stand with the bike. The other person should stand on the opposite side of the bike "just in case".

    Safety is paramount and no personal injury is worth a dented tank. I always give the same briefing: "Help steady but if it starts to go: RUN!" I painted the top with some Duration exterior house paint to protect it from spills. Please be careful and use your best judgment: Bikes can fall off this stand!






  2. #2
    Baby Twin Badger02's Avatar
    Join Date
    Feb 2008
    Location
    Germany
    Posts
    18
    Nice writeup and pics. Certainly will keep me from breaking my back this winter when I am doing some servicing.

  3. #3
    Baby Twin
    Join Date
    May 2009
    Posts
    45
    genius! and there was me thinking of buying a hydraulic lift as well.

  4. #4
    Baby Twin
    Join Date
    Dec 2014
    Location
    London
    Posts
    16

    Built this ....................Brilliant

    Quote Originally Posted by dipper View Post
    genius! and there was me thinking of buying a hydraulic lift as well.
    Built this.....................brilliant!!!

Similar Discussions

  1. Service what to do ??
    By Goofyfoot08 in forum Aprilia RSVR
    Replies: 4
    Last Post: October 24th, 2010, 12:53 PM
  2. York Weight bench in Widnes
    By jarvis in forum Classifieds
    Replies: 0
    Last Post: February 16th, 2010, 09:54 AM
  3. "Service" still on dash after service
    By Stuza in forum Aprilia RSVR
    Replies: 11
    Last Post: November 8th, 2008, 02:13 AM
  4. Service has ......
    By Gasboy in forum Aprilia RSVR
    Replies: 3
    Last Post: February 18th, 2008, 08:24 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •